Pella 80ED0101 User Manual download pdf

INSTALLATION INSTRUCTIONS - INSTRUCCIONES DE INSTALACION

FOR HURRICANESHIELD

IMPACT-RESISTANT

DOUBLE-HUNG, SINGLE-HUNG AND SIMULATED-HUNG

Part Number: 80ED0101

Instrucciones en español en el reverso.

Fin

Corner

Nailing Fin

Window Bottom

Sill Flashing Tape #2

Sill Flashing Tape #1

Water Resistive Barrier

Sheathing

Framin

Checkrail

Corner

Flashing

Tape

Top

Flashing

Tape

Corner

Flashing

Tape

Side

Flashing

Tape

Side

Flashing

Tape

Window Top

Always read the Pella

™

Limited Warranty before purchasing or installing Pella products. By installing

this product, you are acknowledging that this Limited Warranty is part of the terms of the sale.

Failure to comply with all Pella installation and maintenance instructions may void your Pella

product warranty. See Limited Warranty for complete details at http://www.pella.com.

Important Safety Information:

Pella

HurricaneShield

Products have been tested in accordance with the large missile impact testing

requirements of ASTM E 1886 and ASTM E 1996. Pella HurricaneShield Products are neither

hurricane proof nor are they shatter proof. Severe wind and rain may produce temporary conditions

which exceed product performance standards. When these units are subjected to intense storms or

extreme conditions, which exceed the intended design pressures, air, water and ﬂying debris inﬁltration

may occur.

The performance of any building is dependent upon the design, installation, and workmanship of the

entire building system. Pella Corporation strongly recommends consulting an experienced architect,

contractor, or structural engineer prior to installation of Pella products.

The individual (building owner, architect, contractor, installer and/or consumer) responsible for the

project must take into account local conditions, building codes, inherent component limitations,

the effects of aging and weathering on building components, and other design issues relevant to each

project.

The determination of the suitability of all building components for each project, as well as the design

and installation of ﬂashing and sealing systems, are the responsibility of the building owner, architect,

contractor, installer and/or consumer.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Part Number: 80ED0101

INSTALLATION INSTRUCTIONS - INSTRUCCIONES DE INSTALACIONFOR HURRICANESHIELD® IMPACT-RESISTANT DOUBLE-HUNG, SINGLE-HUNG AND SIMULATED-HUNGPart Number:

Page 2 - 1 ROUGH OPENING PREPARATION

REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.1 ROUGH OPENING PREPARATIONA. Verify the opening is plumb and level. Note: It is critical

Page 3 - 3 SETTING THE WINDOW

2 PREPARE THE WINDOWA. Remove plastic wrap and cardboard packaging from window. DO NOT cut the checkrail bands or remove plastic shipping spacers loc

Page 4 - 4 INSTALLATION CLIP METHOD

4 INSTALLATION CLIP METHODA. Fasten the window to the openingBYDRIVINGTWOXCORROSIONresistant screws into the pre-punched holes in the

Page 5 - 5 FRAME SCREW METHOD

5 FRAME SCREW METHOD5BA. Mark the location of the top of the lower sash on the rough opening.Note: Marking this location is needed for the correct pl

Page 6 - THE WATER RESISTIVE BARRIER

6 INTEGRATING THE WINDOW TO THE WATER RESISTIVE BARRIERNote: The ﬂashing tape must be applied approximately 1/2" onto the frame cladding at the j

Page 7 - 7 INTERIOR SEAL

C. Fold down top ﬂap of water resistive barrier (6C).D. Apply ﬂashing tape to diagonal cuts. Cut pieces of ﬂashing tape at least 1" longer than

Page 8 - IMPORTANT NOTICE

EXTERIOR FINISH The exterior frame and sash are protected by aluminum cladding with our tough EnduraClad® or EnduraClad Plus baked-on factory ﬁnish th

Comments to this Manuals

No comments

Pella 80ED0101 User Manual

Browse online or download User Manual for Unknown Pella 80ED0101. Pella 80ED0101 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Pella 80ED0101